MS42 0110CA 7526753 5WK9020---0174410005
Vehicle & ECU
Software identification 3
0110CA75267535WK9020---0174410005Operations performed 5
-
STAGE1
A safe performance tune that needs no mechanical changes and does not harm the vehicle.
-
REVLIMIT
Adjusts the engine rev limiter (hard cut) point.
-
LAMBDA OFF
Disables the oxygen (lambda) sensors.
-
DECAT
Disables catalytic converter efficiency monitoring and the P0420/P0430 fault codes.
-
POPBANG
Creates exhaust pop & bang / crackle sounds; requires a decatted exhaust with few silencers.
Other solutions for this ECU 10
Every operation below can be ordered for the same MS42 file (petrol). Prices are per file in EUR; automatic solutions are delivered within minutes, engineer-assisted ones are prepared by our tuning team.
About this project
Siemens MS4x is a BMW petrol ECU generation. This unit is fitted to BMW - MINI Car vehicles. Project #4511 was completed automatically by the ECUHARD file service for a BMW - MINI Car vehicle running software 0110CA 7526753 5WK9020---0174410005.
Frequently asked questions
What was done to this MS42 file?
Operations performed: STAGE1, REVLIMIT, LAMBDA OFF, DECAT, POPBANG. The modified file was checksum-corrected and delivered ready to flash.
What is the software version for this MS42 file?
This project is for MS42 with software numbers: 0110CA 7526753, 5WK9020---0174410005. The same operations apply to other vehicles running the same software.
Can I get the same tuning for my BMW - MINI?
Yes. Sign in, upload your original ECU file (MS42 or any supported ECU), choose the operations you need and our automated system prepares the file, usually within minutes, 24/7.
I read my ECU with a different tool — will the tuning fit my file?
Yes. Every operation is applied to the file you upload — your own read from your own car — so the tool and the read mode do not matter: the modifications are located by content, not by a fixed file layout. If your file was modified before, our REV ORI (revert to original) module repairs every changed area back to the stock values first — no matter which tool or method read it (KTAG, KESS, Flex, Autotuner, CMD, OBD, bench or boot) (10 EUR). A compatibility problem is therefore impossible.
I have an OBD read — can you tune it, or do I need a bench/boot read?
An OBD read is fine as long as it contains the software area (maps). Upload it; the platform detects the ECU and software number and shows which operations are available for your file. If the read is partial and an operation is not possible on it, you will see that before paying.
I read boot mode with KTAG / bench with Flex / bench or OBD with Autotuner — which read do I upload?
Any of them. Upload the file exactly as your tool saved it (MS42 reads are supported in OBD, bench and boot form). The system works on your own read, so nothing has to be converted or matched to a different device.
Do you need the full backup (EEPROM, other sectors)?
No. Only the software-related part of the ECU is used: the maps area — the internal flash and/or the external flash, depending on where the software lives in that ECU. EEPROM and other memory sectors are not needed and are never modified. Keep your full backup for yourself as a safety copy.
How can I be sure the result will be compatible with my ECU?
Because the file returned to you is your own read with only the selected areas changed and the checksum corrected, it flashes back with the same tool and method you used to read it. The software number stays the same; nothing else in the file is touched.
What other operations are available for MS42?
STAGE2 (40 EUR, automatic, 6 ready solutions for this file size); VMAX OFF (5 EUR, automatic, 4 ready solutions for this file size); KNOCK OFF (10 EUR, automatic, 2 ready solutions for this file size); MISSFIRE OFF (10 EUR, automatic, 3 ready solutions for this file size); IDLE RPM (10 EUR, automatic, 1 ready solution for this file size); IMMO OFF (50 EUR, automatic, 4 ready solutions for this file size); TERMOSTAT (20 EUR, automatic, 5 ready solutions for this file size); DTC OFF (10 EUR, automatic, instant); CHECKSUM OK (1 EUR, automatic, instant); REV ORI (10 EUR, automatic, stock file in archive). Prices are per file.
I have a MS42 file — how can I get it done?
Sign in to the ECUHARD platform (solutions.ecuhard.com), upload your ECU file, select the operations you need and confirm. Automatic solutions are delivered within minutes, 24/7; engineer-assisted operations are prepared by our tuning team. Each file is checksum-corrected and an invoice is issued automatically.
Do I need to send my original file?
Yes — upload the stock read of your ECU. If you do not have it, our original file archive may have a matching file by software number.