SID203-V8 344KMAW3LP14400 NNS505540 10102308AA
Vehicle & ECU
ECM Titanium
R27_574B · LAND ROVER RANGE ROVER · SID20XSoftware identification 3
344KMAW3LP14400NNS50554010102308AAOperations performed 1
-
DTC OFF
Permanently disables the fault codes (DTC) you select; you need to provide the P codes to turn off.
P0401Exhaust Gas Recirculation Flow Insufficient DetectedP0402Exhaust Gas Recirculation Flow Excessive DetectedP0403Exhaust Gas Recirculation Control CircuitP0405Exhaust Gas Recirculation Sensor "A" Circuit LowP0406Exhaust Gas Recirculation Sensor "A" Circuit HighP0407Exhaust Gas Recirculation Sensor "B" Circuit LowP0408Exhaust Gas Recirculation Sensor "B" Circuit HighP045AEGR "B" Control CircuitP045CEGR "B" Control Circuit LowP045DEGR "B" Control Circuit HighP0488Exhaust Gas Recirculation Throttle Position Control Range/PerformanceP0489Exhaust Gas Recirculation Control Circuit LowP0490Exhaust Gas Recirculation Control Circuit High
Other solutions for this ECU 15
Every operation below can be ordered for the same SID203-V8 file (diesel). Prices are per file in EUR; automatic solutions are delivered within minutes, engineer-assisted ones are prepared by our tuning team.
About this project
Continental/Siemens SID is a diesel ECU family used by Ford, PSA, Renault/Nissan and others. This unit is fitted to LAND ROVER - JAGUAR Car vehicles. Project #27289 was completed automatically by the ECUHARD file service for a LAND ROVER - JAGUAR Car vehicle running software 344KMAW3LP14400 NNS505540 10102308AA. Disabled fault codes: P0401, P0402, P0403, P0405, P0406, P0407, P0408, P045A, P045C, P045D, P0488, P0489, P0490.
Frequently asked questions
What was done to this SID203-V8 file?
Operations performed: DTC OFF. The modified file was checksum-corrected and delivered ready to flash.
Which fault codes (DTC) were disabled?
P0401 (Exhaust Gas Recirculation Flow Insufficient Detected); P0402 (Exhaust Gas Recirculation Flow Excessive Detected); P0403 (Exhaust Gas Recirculation Control Circuit); P0405 (Exhaust Gas Recirculation Sensor "A" Circuit Low); P0406 (Exhaust Gas Recirculation Sensor "A" Circuit High); P0407 (Exhaust Gas Recirculation Sensor "B" Circuit Low); P0408 (Exhaust Gas Recirculation Sensor "B" Circuit High); P045A (EGR "B" Control Circuit); P045C (EGR "B" Control Circuit Low); P045D (EGR "B" Control Circuit High); P0488 (Exhaust Gas Recirculation Throttle Position Control Range/Performance); P0489 (Exhaust Gas Recirculation Control Circuit Low); P0490 (Exhaust Gas Recirculation Control Circuit High). Each code is switched off in the ECU fault table, so it is no longer stored or shown by diagnostic tools.
What is the software version for this SID203-V8 file?
This project is for SID203-V8 with software numbers: 344KMAW3LP14400, NNS505540, 10102308AA. The same operations apply to other vehicles running the same software.
Can I get the same tuning for my LAND ROVER - JAGUAR?
Yes. Sign in, upload your original ECU file (SID203-V8 or any supported ECU), choose the operations you need and our automated system prepares the file, usually within minutes, 24/7.
I read my ECU with a different tool — will the tuning fit my file?
Yes. Every operation is applied to the file you upload — your own read from your own car — so the tool and the read mode do not matter: the modifications are located by content, not by a fixed file layout. If your file was modified before, our REV ORI (revert to original) module repairs every changed area back to the stock values first — no matter which tool or method read it (KTAG, KESS, Flex, Autotuner, CMD, OBD, bench or boot) (20 EUR). A compatibility problem is therefore impossible.
I have an OBD read — can you tune it, or do I need a bench/boot read?
An OBD read is fine as long as it contains the software area (maps). Upload it; the platform detects the ECU and software number and shows which operations are available for your file. If the read is partial and an operation is not possible on it, you will see that before paying.
I read boot mode with KTAG / bench with Flex / bench or OBD with Autotuner — which read do I upload?
Any of them. Upload the file exactly as your tool saved it (SID203-V8 reads are supported in OBD, bench and boot form). The system works on your own read, so nothing has to be converted or matched to a different device.
Do you need the full backup (EEPROM, other sectors)?
No. Only the software-related part of the ECU is used: the maps area — the internal flash and/or the external flash, depending on where the software lives in that ECU. EEPROM and other memory sectors are not needed and are never modified. Keep your full backup for yourself as a safety copy.
How can I be sure the result will be compatible with my ECU?
Because the file returned to you is your own read with only the selected areas changed and the checksum corrected, it flashes back with the same tool and method you used to read it. The software number stays the same; nothing else in the file is touched.
What other operations are available for SID203-V8?
STAGE1 (40 EUR, engineer-assisted, on request); STAGE2 (80 EUR, engineer-assisted, on request); ADBLUE OFF (20 EUR, engineer-assisted, on request); DPF OFF (20 EUR, engineer-assisted, on request); EGR OFF (20 EUR, automatic, 4 ready solutions for this file size); LAMBDA OFF (20 EUR, engineer-assisted, on request); DECAT (20 EUR, engineer-assisted, on request); NOX OFF (20 EUR, engineer-assisted, on request); VMAX (20 EUR, engineer-assisted, on request); TVA OFF (20 EUR, engineer-assisted, on request); FLAPS OFF (20 EUR, engineer-assisted, on request); IMMO OFF (100 EUR, engineer-assisted, on request); HOT START (40 EUR, engineer-assisted, on request); HARDCUT (20 EUR, engineer-assisted, on request); REV ORI (20 EUR, automatic, stock file in archive). Prices are per file.
I have a SID203-V8 file — how can I get it done?
Sign in to the ECUHARD platform (solutions.ecuhard.com), upload your ECU file, select the operations you need and confirm. Automatic solutions are delivered within minutes, 24/7; engineer-assisted operations are prepared by our tuning team. Each file is checksum-corrected and an invoice is issued automatically.
Is there an ECM Titanium driver for this SID203-V8 file?
Yes. The file is linked to ECM Titanium driver R27_574B (LAND ROVER RANGE ROVER). Matched: the software range is identical to the driver reference. The driver tells the software where the maps of this ECU software are, so tools that use ECM drivers, including the ECUHARD Tuning Editor, can open the maps automatically.
Do I need to send my original file?
Yes — upload the stock read of your ECU. If you do not have it, our original file archive may have a matching file by software number.