ECUHARD
Recent Projects
Sign In
Project #4123

EDC16C34 9657699480 9666986880 EDC16C34_PSA

PEUGEOT - CITROEN Car Diesel STAGE1 ✓ Completed Feb 14, 2026

Vehicle & ECU

ECUEDC16C34
Brand groupPEUGEOT - CITROEN
Vehicle typeCar
FuelDiesel
File size2.00 MB 2,097,152 bytes
Completed
Automated processing≈ 15 min
Status✓ Completed & delivered
Original filepsa_bosch_edc16c34_obd_maps_20260214175612.bin

Software identification 3

Software number9657699480
Identifier 29666986880
Identifier 3EDC16C34_PSA

Operations performed 1

  1. STAGE1 automated · solution rev 29 · ~15 min

    A safe performance tune that needs no mechanical changes and does not harm the vehicle.

Other solutions for this ECU 13

Every operation below can be ordered for the same EDC16C34 file (diesel). Prices are per file in EUR; automatic solutions are delivered within minutes, engineer-assisted ones are prepared by our tuning team.

STAGE1 A safe performance tune that needs no mechanical changes and does not harm the vehicle. done in this project ✓
STAGE2 A performance tune that requires hardware changes such as exhaust, filter or DPF removal. automatic, 7 ready solutions for this file size · ~60 min 40 EUR
STAGE3 A performance tune built from data logs after vehicle-specific hardware upgrades. engineer-assisted, on request · ~180 min 200 EUR
DPF OFF Deletes the diesel particulate filter (DPF) system in software; if the vehicle has AdBlue, it must be deleted first. automatic, 35 ready solutions for this file size · ~5 min 5 EUR
EGR OFF Disables the exhaust gas recirculation (EGR) system. automatic, 58 ready solutions for this file size · ~5 min 5 EUR
LAMBDA OFF Disables the oxygen (lambda) sensors. automatic, 15 ready solutions for this file size · ~5 min 5 EUR
VMAX OFF Removes the speed limiter (Vmax) or sets it to the desired value. automatic, 7 ready solutions for this file size · ~5 min 5 EUR
TVA OFF Disables the diesel throttle valve. automatic, 3 ready solutions for this file size · ~5 min 5 EUR
FLAPS OFF Disables the swirl flaps in the intake manifold. automatic, 5 ready solutions for this file size · ~5 min 5 EUR
IMMO OFF automatic, 5 ready solutions in library · ~180 min 50 EUR
REVLIMIT Adjusts the engine rev limiter (hard cut) point. automatic, instant 10 EUR
DTC OFF Permanently disables the fault codes (DTC) you select; you need to provide the P codes to turn off. automatic, instant 10 EUR
CHECKSUM OK Automatically calculates and corrects your modified file’s checksum; if your tool cannot do checksums, we do it for you. automatic, instant 1 EUR
REV ORI engineer-assisted, on request · ~120 min 10 EUR
Have a EDC16C34 file? Sign in to the ECUHARD platform, upload it and pick the operations — automatic solutions are ready in minutes, 24/7, invoice issued automatically.
Sign in & upload your file →

About this project

Bosch EDC16 is a common-rail / unit-injector diesel ECU generation used across many brands from 2003 onward. This unit is fitted to PEUGEOT - CITROEN Car vehicles. Project #4123 was completed automatically by the ECUHARD file service for a PEUGEOT - CITROEN Car vehicle running software 9657699480 9666986880 EDC16C34_PSA.

Frequently asked questions

What was done to this EDC16C34 file?

Operations performed: STAGE1. The modified file was checksum-corrected and delivered ready to flash.

What is the software version for this EDC16C34 file?

This project is for EDC16C34 with software numbers: 9657699480, 9666986880, EDC16C34_PSA. The same operations apply to other vehicles running the same software.

Can I get the same tuning for my PEUGEOT - CITROEN?

Yes. Sign in, upload your original ECU file (EDC16C34 or any supported ECU), choose the operations you need and our automated system prepares the file, usually within minutes, 24/7.

I read my ECU with a different tool — will the tuning fit my file?

Yes. Every operation is applied to the file you upload — your own read from your own car — so the tool and the read mode do not matter: the modifications are located by content, not by a fixed file layout. If your file was modified before, our REV ORI (revert to original) module repairs every changed area back to the stock values first — no matter which tool or method read it (KTAG, KESS, Flex, Autotuner, CMD, OBD, bench or boot) (10 EUR). A compatibility problem is therefore impossible.

I have an OBD read — can you tune it, or do I need a bench/boot read?

An OBD read is fine as long as it contains the software area (maps). Upload it; the platform detects the ECU and software number and shows which operations are available for your file. If the read is partial and an operation is not possible on it, you will see that before paying.

I read boot mode with KTAG / bench with Flex / bench or OBD with Autotuner — which read do I upload?

Any of them. Upload the file exactly as your tool saved it (EDC16C34 reads are supported in OBD, bench and boot form). The system works on your own read, so nothing has to be converted or matched to a different device.

Do you need the full backup (EEPROM, other sectors)?

No. Only the software-related part of the ECU is used: the maps area — the internal flash and/or the external flash, depending on where the software lives in that ECU. EEPROM and other memory sectors are not needed and are never modified. Keep your full backup for yourself as a safety copy.

How can I be sure the result will be compatible with my ECU?

Because the file returned to you is your own read with only the selected areas changed and the checksum corrected, it flashes back with the same tool and method you used to read it. The software number stays the same; nothing else in the file is touched.

What other operations are available for EDC16C34?

STAGE2 (40 EUR, automatic, 7 ready solutions for this file size); STAGE3 (200 EUR, engineer-assisted, on request); DPF OFF (5 EUR, automatic, 35 ready solutions for this file size); EGR OFF (5 EUR, automatic, 58 ready solutions for this file size); LAMBDA OFF (5 EUR, automatic, 15 ready solutions for this file size); VMAX OFF (5 EUR, automatic, 7 ready solutions for this file size); TVA OFF (5 EUR, automatic, 3 ready solutions for this file size); FLAPS OFF (5 EUR, automatic, 5 ready solutions for this file size); IMMO OFF (50 EUR, automatic, 5 ready solutions in library); REVLIMIT (10 EUR, automatic, instant); DTC OFF (10 EUR, automatic, instant); CHECKSUM OK (1 EUR, automatic, instant); REV ORI (10 EUR, engineer-assisted, on request). Prices are per file.

I have a EDC16C34 file — how can I get it done?

Sign in to the ECUHARD platform (solutions.ecuhard.com), upload your ECU file, select the operations you need and confirm. Automatic solutions are delivered within minutes, 24/7; engineer-assisted operations are prepared by our tuning team. Each file is checksum-corrected and an invoice is issued automatically.

Do I need to send my original file?

Yes — upload the stock read of your ECU. If you do not have it, our original file archive may have a matching file by software number.