Project #519

MD1CS006 - MD1CS016 MCE3867TGLMRH78881673 237018877S 10SW050224 10SW086885

RENAULT - NISSAN Car Diesel EGR OFF ✓ Completed Nov 6, 2025

Vehicle & ECU

Brand groupRENAULT - NISSAN
Vehicle typeCar
FuelDiesel
File size8.00 MB 8,388,608 bytes
Completed
Automated processing≈ 5 min
Status✓ Completed & delivered
Original fileRackMultipart20251106-2632253-1fvnlvz_int_flash.bin
Stock fileUploaded file was already modified (not a stock read)

Software identification 4

Software numberMCE3867TGLMRH78881673
Identifier 2237018877S
Identifier 310SW050224
Identifier 410SW086885

Operations performed 1

  1. EGR OFF automated · solution rev 14 · ~5 min

    Disables the exhaust gas recirculation (EGR) system.

Other solutions for this ECU 14

Every operation below can be ordered for the same MD1CS006 - MD1CS016 file (diesel). Prices are per file in EUR; automatic solutions are delivered within minutes, engineer-assisted ones are prepared by our tuning team.

STAGE1 A safe performance tune that needs no mechanical changes and does not harm the vehicle. automatic, 19 ready solutions for this file size · ~15 min 50 EUR
STAGE2 A performance tune that requires hardware changes such as exhaust, filter or DPF removal. automatic, 1 ready solution for this file size · ~60 min 200 EUR
ADBLUE OFF Disables the AdBlue (SCR) system in software; no AdBlue refills are needed afterwards. automatic, 44 ready solutions for this file size · ~10 min 25 EUR
DPF OFF Deletes the diesel particulate filter (DPF) system in software; if the vehicle has AdBlue, it must be deleted first. automatic, 34 ready solutions for this file size · ~5 min 25 EUR
EGR OFF Disables the exhaust gas recirculation (EGR) system. done in this project
LAMBDA OFF Disables the oxygen (lambda) sensors. automatic, 14 ready solutions for this file size · ~5 min 25 EUR
DECAT Disables catalytic converter efficiency monitoring and the P0420/P0430 fault codes. automatic, 3 ready solutions for this file size · ~5 min 25 EUR
NOX OFF Disables the NOx sensor. automatic, 19 ready solutions for this file size · ~5 min 25 EUR
VMAX OFF Removes the speed limiter (Vmax) or sets it to the desired value. automatic, 5 ready solutions for this file size · ~5 min 25 EUR
FLAPS OFF Disables the swirl flaps in the intake manifold. automatic, 5 ready solutions for this file size · ~5 min 25 EUR
STARTSTOP OFF Permanently disables the Start/Stop system. engineer-assisted, on request · ~20 min 200 EUR
IMMO OFF automatic, 2 ready solutions for this file size · ~180 min 250 EUR
REVLIMIT Adjusts the engine rev limiter (hard cut) point. automatic, 2 ready solutions for this file size · ~20 min 50 EUR
DTC OFF Permanently disables the fault codes (DTC) you select; you need to provide the P codes to turn off. automatic, instant 50 EUR
REV ORI engineer-assisted, on request · ~120 min 50 EUR
Have a MD1CS006 - MD1CS016 file? Sign in to the ECUHARD platform, upload it and pick the operations — automatic solutions are ready in minutes, 24/7, invoice issued automatically.
Sign in & upload your file →

About this project

Bosch MD1 is a current-generation diesel ECU (Euro 6) with advanced emission control. This unit is fitted to RENAULT - NISSAN Car vehicles. Project #519 was completed automatically by the ECUHARD file service for a RENAULT - NISSAN Car vehicle running software MCE3867TGLMRH78881673 237018877S 10SW050224 10SW086885.

Frequently asked questions

What was done to this MD1CS006 - MD1CS016 file?

Operations performed: EGR OFF. The modified file was checksum-corrected and delivered ready to flash.

What is the software version for this MD1CS006 - MD1CS016 file?

This project is for MD1CS006 - MD1CS016 with software numbers: MCE3867TGLMRH78881673, 237018877S, 10SW050224, 10SW086885. The same operations apply to other vehicles running the same software.

Can I get the same tuning for my RENAULT - NISSAN?

Yes. Sign in, upload your original ECU file (MD1CS006 - MD1CS016 or any supported ECU), choose the operations you need and our automated system prepares the file, usually within minutes, 24/7.

I read my ECU with a different tool — will the tuning fit my file?

Yes. Every operation is applied to the file you upload — your own read from your own car — so the tool and the read mode do not matter: the modifications are located by content, not by a fixed file layout. If your file was modified before, our REV ORI (revert to original) module repairs every changed area back to the stock values first — no matter which tool or method read it (KTAG, KESS, Flex, Autotuner, CMD, OBD, bench or boot) (50 EUR). A compatibility problem is therefore impossible.

I have an OBD read — can you tune it, or do I need a bench/boot read?

An OBD read is fine as long as it contains the software area (maps). Upload it; the platform detects the ECU and software number and shows which operations are available for your file. If the read is partial and an operation is not possible on it, you will see that before paying.

I read boot mode with KTAG / bench with Flex / bench or OBD with Autotuner — which read do I upload?

Any of them. Upload the file exactly as your tool saved it (MD1CS006 - MD1CS016 reads are supported in OBD, bench and boot form). The system works on your own read, so nothing has to be converted or matched to a different device.

Do you need the full backup (EEPROM, other sectors)?

No. Only the software-related part of the ECU is used: the maps area — the internal flash and/or the external flash, depending on where the software lives in that ECU. EEPROM and other memory sectors are not needed and are never modified. Keep your full backup for yourself as a safety copy.

How can I be sure the result will be compatible with my ECU?

Because the file returned to you is your own read with only the selected areas changed and the checksum corrected, it flashes back with the same tool and method you used to read it. The software number stays the same; nothing else in the file is touched.

What other operations are available for MD1CS006 - MD1CS016?

STAGE1 (50 EUR, automatic, 19 ready solutions for this file size); STAGE2 (200 EUR, automatic, 1 ready solution for this file size); ADBLUE OFF (25 EUR, automatic, 44 ready solutions for this file size); DPF OFF (25 EUR, automatic, 34 ready solutions for this file size); LAMBDA OFF (25 EUR, automatic, 14 ready solutions for this file size); DECAT (25 EUR, automatic, 3 ready solutions for this file size); NOX OFF (25 EUR, automatic, 19 ready solutions for this file size); VMAX OFF (25 EUR, automatic, 5 ready solutions for this file size); FLAPS OFF (25 EUR, automatic, 5 ready solutions for this file size); STARTSTOP OFF (200 EUR, engineer-assisted, on request); IMMO OFF (250 EUR, automatic, 2 ready solutions for this file size); REVLIMIT (50 EUR, automatic, 2 ready solutions for this file size); DTC OFF (50 EUR, automatic, instant); REV ORI (50 EUR, engineer-assisted, on request). Prices are per file.

I have a MD1CS006 - MD1CS016 file — how can I get it done?

Sign in to the ECUHARD platform (solutions.ecuhard.com), upload your ECU file, select the operations you need and confirm. Automatic solutions are delivered within minutes, 24/7; engineer-assisted operations are prepared by our tuning team. Each file is checksum-corrected and an invoice is issued automatically.

Do I need to send my original file?

Yes — upload the stock read of your ECU. If you do not have it, our original file archive may have a matching file by software number.