ECUHARD
Recent Projects
Sign In
Project #19035

S3000 8200874498

RENAULT - NISSAN Car Petrol LAMBDA OFF + DECAT ✓ Completed Sep 1, 2026

Vehicle & ECU

ECUS3000
Brand groupRENAULT - NISSAN
Vehicle typeCar
FuelPetrol
File size64.00 KB 65,536 bytes
Completed
Automated processing≈ 10 min
Status✓ Completed & delivered
Original file48BBP532_ILK.bin
Stock fileStock file in ORI archive (#32976) →

Software identification 1

Software number8200874498

Operations performed 2

  1. LAMBDA OFF automated · solution rev 6 · ~5 min

    Disables the oxygen (lambda) sensors.

  2. DECAT automated · solution rev 2 · ~5 min

    Disables catalytic converter efficiency monitoring and the P0420/P0430 fault codes.

Other solutions for this ECU 7

Every operation below can be ordered for the same S3000 file (petrol). Prices are per file in EUR; automatic solutions are delivered within minutes, engineer-assisted ones are prepared by our tuning team.

STAGE1 A safe performance tune that needs no mechanical changes and does not harm the vehicle. automatic, 1 ready solution in library · ~15 min 10 EUR
STAGE2 A performance tune that requires hardware changes such as exhaust, filter or DPF removal. automatic, 1 ready solution in library · ~60 min 40 EUR
LAMBDA OFF Disables the oxygen (lambda) sensors. done in this project ✓
DECAT Disables catalytic converter efficiency monitoring and the P0420/P0430 fault codes. done in this project ✓
POPBANG Creates exhaust pop & bang / crackle sounds; requires a decatted exhaust with few silencers. automatic, 1 ready solution in library · ~15 min 20 EUR
IMMO OFF engineer-assisted, on request · ~180 min 50 EUR
REVLIMIT Adjusts the engine rev limiter (hard cut) point. engineer-assisted, on request · ~20 min 10 EUR
DTC OFF Permanently disables the fault codes (DTC) you select; you need to provide the P codes to turn off. engineer-assisted, on request · ~10 min 10 EUR
REV ORI automatic, stock file in archive · ~120 min 10 EUR
Have a S3000 file? Sign in to the ECUHARD platform, upload it and pick the operations — automatic solutions are ready in minutes, 24/7, invoice issued automatically.
Sign in & upload your file →

About this project

S3000 is an engine control unit (ECU) supported by our automated file service. This unit is fitted to RENAULT - NISSAN Car vehicles. Project #19035 was completed automatically by the ECUHARD file service for a RENAULT - NISSAN Car vehicle running software 8200874498.

Frequently asked questions

What was done to this S3000 file?

Operations performed: LAMBDA OFF, DECAT. The modified file was checksum-corrected and delivered ready to flash.

What is the software version for this S3000 file?

This project is for S3000 with software numbers: 8200874498. The same operations apply to other vehicles running the same software.

Can I get the same tuning for my RENAULT - NISSAN?

Yes. Sign in, upload your original ECU file (S3000 or any supported ECU), choose the operations you need and our automated system prepares the file, usually within minutes, 24/7.

I read my ECU with a different tool — will the tuning fit my file?

Yes. Every operation is applied to the file you upload — your own read from your own car — so the tool and the read mode do not matter: the modifications are located by content, not by a fixed file layout. If your file was modified before, our REV ORI (revert to original) module repairs every changed area back to the stock values first — no matter which tool or method read it (KTAG, KESS, Flex, Autotuner, CMD, OBD, bench or boot) (10 EUR). A compatibility problem is therefore impossible.

I have an OBD read — can you tune it, or do I need a bench/boot read?

An OBD read is fine as long as it contains the software area (maps). Upload it; the platform detects the ECU and software number and shows which operations are available for your file. If the read is partial and an operation is not possible on it, you will see that before paying.

I read boot mode with KTAG / bench with Flex / bench or OBD with Autotuner — which read do I upload?

Any of them. Upload the file exactly as your tool saved it (S3000 reads are supported in OBD, bench and boot form). The system works on your own read, so nothing has to be converted or matched to a different device.

Do you need the full backup (EEPROM, other sectors)?

No. Only the software-related part of the ECU is used: the maps area — the internal flash and/or the external flash, depending on where the software lives in that ECU. EEPROM and other memory sectors are not needed and are never modified. Keep your full backup for yourself as a safety copy.

How can I be sure the result will be compatible with my ECU?

Because the file returned to you is your own read with only the selected areas changed and the checksum corrected, it flashes back with the same tool and method you used to read it. The software number stays the same; nothing else in the file is touched.

What other operations are available for S3000?

STAGE1 (10 EUR, automatic, 1 ready solution in library); STAGE2 (40 EUR, automatic, 1 ready solution in library); POPBANG (20 EUR, automatic, 1 ready solution in library); IMMO OFF (50 EUR, engineer-assisted, on request); REVLIMIT (10 EUR, engineer-assisted, on request); DTC OFF (10 EUR, engineer-assisted, on request); REV ORI (10 EUR, automatic, stock file in archive). Prices are per file.

I have a S3000 file — how can I get it done?

Sign in to the ECUHARD platform (solutions.ecuhard.com), upload your ECU file, select the operations you need and confirm. Automatic solutions are delivered within minutes, 24/7; engineer-assisted operations are prepared by our tuning team. Each file is checksum-corrected and an invoice is issued automatically.

Do I need to send my original file?

Yes — upload the stock read of your ECU. If you do not have it, our original file archive may have a matching file by software number.