Project #27702

EDC17C46 - EDC17C64 03L906018PH 9977

VW - AUDI - SEAT - SKODA - PORSCHE Car Diesel DPF OFF + EGR OFF + LAMBDA OFF + NOX OFF + VMAX + DTC OFF ✓ Completed Nov 14, 2026

Vehicle & ECU

Vehicle typeCar
FuelDiesel
File size2.00 MB 2,097,152 bytes
Completed
Automated processing≈ 35 min
Status✓ Completed & delivered
Original file0281018559 1037521086 03L 906 018 PH_iRom

ECM Titanium

Driver · Vehicle · ECUAXXX773A · AUDI Q3 · EDC17C46

Software identification 2

Software number03L906018PH
Version / upgrade9977

Operations performed 6

  1. DPF OFF automated · solution rev 5 · ~5 min

    Deletes the diesel particulate filter (DPF) system in software; if the DPF and AdBlue (SCR) share one housing, AdBlue must be deleted as well.

  2. EGR OFF automated · solution rev 5 · ~5 min

    Disables the exhaust gas recirculation (EGR) system.

  3. LAMBDA OFF automated · solution rev 29 · ~5 min

    Disables the oxygen (lambda) sensors.

  4. NOX OFF automated · solution rev 8 · ~5 min

    Disables the NOx sensor.

  5. VMAX automated · solution rev 16 · ~5 min

    Removes the speed limiter (Vmax) or sets it to the desired value.

  6. DTC OFF automated · solution rev 1 · ~10 min

    Permanently disables the fault codes (DTC) you select; you need to provide the P codes to turn off.

    • P00D1HO2S Heater Control Circuit Range/Performance Bank 1 Sensor 1
    • P0130O2=Sensor Circuit Bank 1 Sensor 1
    • P0131O2=Sensor Circuit Low Voltage Bank 1 Sensor 1
    • P0132O2=Sensor Circuit High Voltage Bank 1 Sensor 1
    • P0133O2=Sensor Circuit Slow Response Bank 1 Sensor 1
    • P0134O2=Sensor Circuit No Activity Detected Bank 1 Sensor 1
    • P0135O2=Sensor Heater Circuit Bank 1 Sensor 1
    • P0400Exhaust Gas Recirculation Flow
    • P0401Exhaust Gas Recirculation Flow Insufficient Detected
    • P0402Exhaust Gas Recirculation Flow Excessive Detected
    • P0403Exhaust Gas Recirculation Control Circuit
    • P0404Exhaust Gas Recirculation Control Circuit Range/Performance
    • P0405Exhaust Gas Recirculation Sensor "A" Circuit Low
    • P0406Exhaust Gas Recirculation Sensor "A" Circuit High
    • P040BEGR Temperature Sensor "A" Circuit Range/Performance
    • P0420Catalyst System Efficiency Below Threshold Bank 1
    • P046CEGR Sensor "A" Circuit Range/Performance
    • P050ECold Start Engine Exhaust Temperature Too Low
    • P0544Exhaust Gas Temperature Sensor Circuit Bank 1 Sensor 1
    • P0545Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 1
    • P1127Exhaust Not Warm, Downstream O2
    • P1128Upstream Heated O2 Sensors Swapped
    • P1129Downstream Heated O2 Sensors Swapped
    • P1133HO2S Insufficient Switching Sensor 1
    • P1134HO2S Transition Time Ratio Sensor
    • P1137Lack Of HO2S Switch -
    • P1138Lack Of HO2S12 Switch -
    • P1313Misfire Rate Catalyst Damage Fault
    • P13F6The engine cannot be started because of SCR faults
    • P1402EGR Metering Orifice Restricted
    • P1406Exhaust Gas Recirculation (EGR) Position
    • P1407EGR No Flow Detected
    • P1408EGR Flow Out Of Self
    • P1420Catalyst Temperature Sensor Failure
    • P1485EGRV Circuit Malfunction
    • P1489EGR Flow Insufficient Detected
    • P2002Particulate Trap Efficiency Below Threshold Bank 1
    • P2031Exhaust Gas Temperature Sensor Circuit Bank 1 Sensor 2
    • P2032Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 2
    • P2080Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1
    • P2084Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2
    • P20EESCR NOx Catalyst Efficiency Below Threshold Bank 1
    • P2195O2=Sensor Signal Stuck Lean Bank 1 Sensor 1
    • P2196O2=Sensor Signal Stuck Rich Bank 1 Sensor 1
    • P2200NOx Sensor Circuit Bank 1
    • P2201NOx Sensor Circuit Range/Performance Bank 1
    • P2202NOx Sensor Circuit Low Input Bank 1
    • P2203NOx Sensor Circuit High Input Bank 1
    • P2209NOx Sensor Heater Sense Circuit Range/Performance Bank 1
    • P2220NOx Sensor Heater Control Circuit High Bank 2
    • P2221NOx Sensor Heater Sense Circuit Bank 2
    • P2222NOx Sensor Heater Sense Circuit Range/Performance Bank 2
    • P2237O2 Sensor Positive Current Control Circuit/Open Bank 1 Sensor 1
    • P2243O2 Sensor Reference Voltage Circuit/Open Bank 1 Sensor 1
    • P2251O2 Sensor Negative Current Control Circuit/Open Bank 1 Sensor 1
    • P2297O2=Sensor Out of Range During Deceleration Bank 1 Sensor 1
    • P229FNOx Sensor Circuit Range/Performance Bank 1 Sensor 2
    • P22A0NOx Sensor Circuit Low Bank 1 Sensor 2
    • P22A1NOx Sensor Circuit High Bank 1 Sensor 2
    • P22A7NOx Sensor Heater Sense Circuit Range/Performance Bank 1 Sensor 2
    • P23A0O2 Sensor Exhaust Sample Error Bank 1 Sensor 2
    • P23A1O2 Sensor Exhaust Sample Error Bank 2 Sensor 2
    • P23A3Exhaust Heat Exchanger Exhaust Bypass Valve "B" Control Circuit Low
    • P23A4Exhaust Heat Exchanger Exhaust Bypass Valve "B" Control Circuit High
    • P23A6Exhaust Heat Exchanger Exhaust Bypass Valve "B" Stuck Open
    • P23A7Exhaust Heat Exchanger Exhaust Bypass Valve "B" Stuck Closed
    • P23E1EGR "C" Control Circuit/Open
    • P23E2EGR "C" Control Circuit Performance
    • P240FEGR Slow Response
    • P2414O2=Sensor Exhaust Sample Error Bank 1 Sensor 1
    • P2425Exhaust Gas Recirculation Cooling Valve Control Circuit/Open
    • P2426Exhaust Gas Recirculation Cooling Valve Control Circuit Low
    • P2427Exhaust Gas Recirculation Cooling Valve Control Circuit High
    • P242AExhaust Gas Temperature Sensor Circuit Bank 1 Sensor 3
    • P242BExhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 3
    • P242CExhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 3
    • P242FParticulate Filter Restriction - Ash Accumulation Bank 1
    • P244CExhaust Temperature Too Low For Particulate Filter Regeneration Bank 1
    • P2456Particulate Filter Pressure Sensor "A" Circuit Intermittent/Erratic
    • P246EExhaust Gas Temperature Sensor Circuit Bank 1 Sensor 4
    • P246FExhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 4
    • P2470Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 4
    • P2478Exhaust Gas Temperature Out of Range Bank 1 Sensor 1
    • P247AExhaust Gas Temperature Out of Range Bank 1 Sensor 3
    • P25D6Exhaust Heat Exchanger Exhaust Bypass Valve "A" Position Sensor Stop Performance
    • P2697Exhaust Aftertreatment Fuel Injector "A" Circuit/Open
    • P2698Exhaust Aftertreatment Fuel Injector "A" Performance
    • P2BD3Exhaust Aftertreatment System "B" Leak
    • P2BF4Exhaust Flow Control Valve "A" Position Circuit
    • P2BF5Exhaust Flow Control Valve "A" Position Circuit Range/Performance
    • P2BFBExhaust Flow Control Valve "B" Control Performance
    • P2C22Exhaust Heat Exchanger Exhaust Bypass Valve "A" Position Sensor Circuit
    • P2C23Exhaust Heat Exchanger Exhaust Bypass Valve "A" Position Sensor Performance

Other solutions for this ECU 12

Every operation below can be ordered for the same EDC17C46 - EDC17C64 file (diesel). Prices are per file in EUR; automatic solutions are delivered within minutes, engineer-assisted ones are prepared by our tuning team.

STAGE1 A performance tune that needs no mechanical changes and stays within the factory safety limits. automatic, 87 ready solutions for this file size · ~15 min 30 EUR
STAGE2 A performance tune for vehicles with hardware upgrades such as a downpipe, intercooler or intake; DPF/EGR delete is a separate operation. automatic, 19 ready solutions for this file size · ~60 min 60 EUR
STAGE3 A performance tune built from data logs after vehicle-specific hardware upgrades. engineer-assisted, on request · ~180 min 300 EUR
ADBLUE OFF Disables the AdBlue (SCR) system in software; no AdBlue refills are needed afterwards. automatic, 32 ready solutions for this file size · ~10 min 15 EUR
DPF OFF Deletes the diesel particulate filter (DPF) system in software; if the DPF and AdBlue (SCR) share one housing, AdBlue must be deleted as well. done in this project ✓
EGR OFF Disables the exhaust gas recirculation (EGR) system. done in this project ✓
LAMBDA OFF Disables the oxygen (lambda) sensors. done in this project ✓
NOX OFF Disables the NOx sensor. done in this project ✓
VMAX Removes the speed limiter (Vmax) or sets it to the desired value. done in this project ✓
TVA OFF Disables the diesel throttle valve. automatic, 14 ready solutions for this file size · ~5 min 15 EUR
FLAPS OFF Disables the swirl flaps in the intake manifold. automatic, 14 ready solutions for this file size · ~5 min 15 EUR
MAF OFF Disables the mass air flow (MAF) sensor. automatic, 8 ready solutions for this file size · ~10 min 45 EUR
STARTSTOP OFF Permanently disables the Start/Stop system. automatic, 4 ready solutions for this file size · ~20 min 60 EUR
IMMO OFF Disables the immobilizer system so the vehicle can start and run. automatic, 6 ready solutions for this file size · ~180 min 75 EUR
WATERPUMP OFF Disables the water pump fault code. automatic, 17 ready solutions for this file size · ~5 min 15 EUR
HARDCUT Sets the engine hardcut (rev cut) point. automatic, 14 ready solutions for this file size · ~20 min 15 EUR
DTC OFF Permanently disables the fault codes (DTC) you select; you need to provide the P codes to turn off. done in this project ✓
REV ORI Restores your modified software file to its original factory state. automatic, stock file in archive · ~120 min 15 EUR
Have a EDC17C46 - EDC17C64 file? Sign in to the ECUHARD platform, upload it and pick the operations — automatic solutions are ready in minutes, 24/7, invoice issued automatically.
Sign in & upload your file →

About this project

Bosch EDC17 is a widely used common-rail diesel ECU generation (Euro 4–6) with DFES fault-code tables. This unit is fitted to VW - AUDI - SEAT - SKODA - PORSCHE Car vehicles. Project #27702 was completed automatically by the ECUHARD file service for a VW - AUDI - SEAT - SKODA - PORSCHE Car vehicle running software 03L906018PH 9977. Disabled fault codes: P00D1, P0130, P0131, P0132, P0133, P0134, P0135, P0400, P0401, P0402, P0403, P0404, P0405, P0406, P040B, P0420, P046C, P050E, P0544, P0545, P1127, P1128, P1129, P1133, P1134, P1137, P1138, P1313, P13F6, P1402, P1406, P1407, P1408, P1420, P1485, P1489, P2002, P2031, P2032, P2080, P2084, P20EE, P2195, P2196, P2200, P2201, P2202, P2203, P2209, P2220, P2221, P2222, P2237, P2243, P2251, P2297, P229F, P22A0, P22A1, P22A7, P23A0, P23A1, P23A3, P23A4, P23A6, P23A7, P23E1, P23E2, P240F, P2414, P2425, P2426, P2427, P242A, P242B, P242C, P242F, P244C, P2456, P246E, P246F, P2470, P2478, P247A, P25D6, P2697, P2698, P2BD3, P2BF4, P2BF5, P2BFB, P2C22, P2C23.

Frequently asked questions

What was done to this EDC17C46 - EDC17C64 file?

Operations performed: DPF OFF, EGR OFF, LAMBDA OFF, NOX OFF, VMAX, DTC OFF. The modified file was checksum-corrected and delivered ready to flash.

Which fault codes (DTC) were disabled?

P00D1 (HO2S Heater Control Circuit Range/Performance Bank 1 Sensor 1); P0130 (O2=Sensor Circuit Bank 1 Sensor 1); P0131 (O2=Sensor Circuit Low Voltage Bank 1 Sensor 1); P0132 (O2=Sensor Circuit High Voltage Bank 1 Sensor 1); P0133 (O2=Sensor Circuit Slow Response Bank 1 Sensor 1); P0134 (O2=Sensor Circuit No Activity Detected Bank 1 Sensor 1); P0135 (O2=Sensor Heater Circuit Bank 1 Sensor 1); P0400 (Exhaust Gas Recirculation Flow); P0401 (Exhaust Gas Recirculation Flow Insufficient Detected); P0402 (Exhaust Gas Recirculation Flow Excessive Detected); P0403 (Exhaust Gas Recirculation Control Circuit); P0404 (Exhaust Gas Recirculation Control Circuit Range/Performance); P0405 (Exhaust Gas Recirculation Sensor "A" Circuit Low); P0406 (Exhaust Gas Recirculation Sensor "A" Circuit High); P040B (EGR Temperature Sensor "A" Circuit Range/Performance); P0420 (Catalyst System Efficiency Below Threshold Bank 1); P046C (EGR Sensor "A" Circuit Range/Performance); P050E (Cold Start Engine Exhaust Temperature Too Low); P0544 (Exhaust Gas Temperature Sensor Circuit Bank 1 Sensor 1); P0545 (Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 1); P1127 (Exhaust Not Warm, Downstream O2); P1128 (Upstream Heated O2 Sensors Swapped); P1129 (Downstream Heated O2 Sensors Swapped); P1133 (HO2S Insufficient Switching Sensor 1); P1134 (HO2S Transition Time Ratio Sensor); P1137 (Lack Of HO2S Switch -); P1138 (Lack Of HO2S12 Switch -); P1313 (Misfire Rate Catalyst Damage Fault); P13F6 (The engine cannot be started because of SCR faults); P1402 (EGR Metering Orifice Restricted); P1406 (Exhaust Gas Recirculation (EGR) Position); P1407 (EGR No Flow Detected); P1408 (EGR Flow Out Of Self); P1420 (Catalyst Temperature Sensor Failure); P1485 (EGRV Circuit Malfunction); P1489 (EGR Flow Insufficient Detected); P2002 (Particulate Trap Efficiency Below Threshold Bank 1); P2031 (Exhaust Gas Temperature Sensor Circuit Bank 1 Sensor 2); P2032 (Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 2); P2080 (Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1); P2084 (Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2); P20EE (SCR NOx Catalyst Efficiency Below Threshold Bank 1); P2195 (O2=Sensor Signal Stuck Lean Bank 1 Sensor 1); P2196 (O2=Sensor Signal Stuck Rich Bank 1 Sensor 1); P2200 (NOx Sensor Circuit Bank 1); P2201 (NOx Sensor Circuit Range/Performance Bank 1); P2202 (NOx Sensor Circuit Low Input Bank 1); P2203 (NOx Sensor Circuit High Input Bank 1); P2209 (NOx Sensor Heater Sense Circuit Range/Performance Bank 1); P2220 (NOx Sensor Heater Control Circuit High Bank 2); P2221 (NOx Sensor Heater Sense Circuit Bank 2); P2222 (NOx Sensor Heater Sense Circuit Range/Performance Bank 2); P2237 (O2 Sensor Positive Current Control Circuit/Open Bank 1 Sensor 1); P2243 (O2 Sensor Reference Voltage Circuit/Open Bank 1 Sensor 1); P2251 (O2 Sensor Negative Current Control Circuit/Open Bank 1 Sensor 1); P2297 (O2=Sensor Out of Range During Deceleration Bank 1 Sensor 1); P229F (NOx Sensor Circuit Range/Performance Bank 1 Sensor 2); P22A0 (NOx Sensor Circuit Low Bank 1 Sensor 2); P22A1 (NOx Sensor Circuit High Bank 1 Sensor 2); P22A7 (NOx Sensor Heater Sense Circuit Range/Performance Bank 1 Sensor 2); P23A0 (O2 Sensor Exhaust Sample Error Bank 1 Sensor 2); P23A1 (O2 Sensor Exhaust Sample Error Bank 2 Sensor 2); P23A3 (Exhaust Heat Exchanger Exhaust Bypass Valve "B" Control Circuit Low); P23A4 (Exhaust Heat Exchanger Exhaust Bypass Valve "B" Control Circuit High); P23A6 (Exhaust Heat Exchanger Exhaust Bypass Valve "B" Stuck Open); P23A7 (Exhaust Heat Exchanger Exhaust Bypass Valve "B" Stuck Closed); P23E1 (EGR "C" Control Circuit/Open); P23E2 (EGR "C" Control Circuit Performance); P240F (EGR Slow Response); P2414 (O2=Sensor Exhaust Sample Error Bank 1 Sensor 1); P2425 (Exhaust Gas Recirculation Cooling Valve Control Circuit/Open); P2426 (Exhaust Gas Recirculation Cooling Valve Control Circuit Low); P2427 (Exhaust Gas Recirculation Cooling Valve Control Circuit High); P242A (Exhaust Gas Temperature Sensor Circuit Bank 1 Sensor 3); P242B (Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 3); P242C (Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 3); P242F (Particulate Filter Restriction - Ash Accumulation Bank 1); P244C (Exhaust Temperature Too Low For Particulate Filter Regeneration Bank 1); P2456 (Particulate Filter Pressure Sensor "A" Circuit Intermittent/Erratic); P246E (Exhaust Gas Temperature Sensor Circuit Bank 1 Sensor 4); P246F (Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 4); P2470 (Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 4); P2478 (Exhaust Gas Temperature Out of Range Bank 1 Sensor 1); P247A (Exhaust Gas Temperature Out of Range Bank 1 Sensor 3); P25D6 (Exhaust Heat Exchanger Exhaust Bypass Valve "A" Position Sensor Stop Performance); P2697 (Exhaust Aftertreatment Fuel Injector "A" Circuit/Open); P2698 (Exhaust Aftertreatment Fuel Injector "A" Performance); P2BD3 (Exhaust Aftertreatment System "B" Leak); P2BF4 (Exhaust Flow Control Valve "A" Position Circuit); P2BF5 (Exhaust Flow Control Valve "A" Position Circuit Range/Performance); P2BFB (Exhaust Flow Control Valve "B" Control Performance); P2C22 (Exhaust Heat Exchanger Exhaust Bypass Valve "A" Position Sensor Circuit); P2C23 (Exhaust Heat Exchanger Exhaust Bypass Valve "A" Position Sensor Performance). Each code is switched off in the ECU fault table, so it is no longer stored or shown by diagnostic tools.

What is the software version for this EDC17C46 - EDC17C64 file?

This project is for EDC17C46 - EDC17C64 with software numbers: 03L906018PH 9977. The same operations apply to other vehicles running the same software.

Can I get the same tuning for my VW - AUDI - SEAT - SKODA - PORSCHE?

Yes. Sign in, upload your original ECU file (EDC17C46 - EDC17C64 or any supported ECU), choose the operations you need and our automated system prepares the file, usually within minutes, 24/7.

I read my ECU with a different tool — will the tuning fit my file?

Yes. Every operation is applied to the file you upload — your own read from your own car — so the tool and the read mode do not matter: the modifications are located by content, not by a fixed file layout. If your file was modified before, our REV ORI (revert to original) module repairs every changed area back to the stock values first — no matter which tool or method read it (KTAG, KESS, Flex, Autotuner, CMD, OBD, bench or boot) (15 EUR). A compatibility problem is therefore impossible.

I have an OBD read — can you tune it, or do I need a bench/boot read?

An OBD read is fine as long as it contains the software area (maps). Upload it; the platform detects the ECU and software number and shows which operations are available for your file. If the read is partial and an operation is not possible on it, you will see that before paying.

I read boot mode with KTAG / bench with Flex / bench or OBD with Autotuner — which read do I upload?

Any of them. Upload the file exactly as your tool saved it (EDC17C46 - EDC17C64 reads are supported in OBD, bench and boot form). The system works on your own read, so nothing has to be converted or matched to a different device.

Do you need the full backup (EEPROM, other sectors)?

No. Only the software-related part of the ECU is used: the maps area — the internal flash and/or the external flash, depending on where the software lives in that ECU. EEPROM and other memory sectors are not needed and are never modified. Keep your full backup for yourself as a safety copy.

How can I be sure the result will be compatible with my ECU?

Because the file returned to you is your own read with only the selected areas changed and the checksum corrected, it flashes back with the same tool and method you used to read it. The software number stays the same; nothing else in the file is touched.

What other operations are available for EDC17C46 - EDC17C64?

STAGE1 (30 EUR, automatic, 87 ready solutions for this file size); STAGE2 (60 EUR, automatic, 19 ready solutions for this file size); STAGE3 (300 EUR, engineer-assisted, on request); ADBLUE OFF (15 EUR, automatic, 32 ready solutions for this file size); TVA OFF (15 EUR, automatic, 14 ready solutions for this file size); FLAPS OFF (15 EUR, automatic, 14 ready solutions for this file size); MAF OFF (45 EUR, automatic, 8 ready solutions for this file size); STARTSTOP OFF (60 EUR, automatic, 4 ready solutions for this file size); IMMO OFF (75 EUR, automatic, 6 ready solutions for this file size); WATERPUMP OFF (15 EUR, automatic, 17 ready solutions for this file size); HARDCUT (15 EUR, automatic, 14 ready solutions for this file size); REV ORI (15 EUR, automatic, stock file in archive). Prices are per file.

I have a EDC17C46 - EDC17C64 file — how can I get it done?

Sign in to the ECUHARD platform (solutions.ecuhard.com), upload your ECU file, select the operations you need and confirm. Automatic solutions are delivered within minutes, 24/7; engineer-assisted operations are prepared by our tuning team. Each file is checksum-corrected and an invoice is issued automatically.

Is there an ECM Titanium driver for this EDC17C46 - EDC17C64 file?

Yes. The file is linked to ECM Titanium driver AXXX773A (AUDI Q3). Matched: the software range is identical to the driver reference. The driver tells the software where the maps of this ECU software are, so tools that use ECM drivers, including the ECUHARD Tuning Editor, can open the maps automatically.

Do I need to send my original file?

Yes — upload the stock read of your ECU. If you do not have it, our original file archive may have a matching file by software number.